Banjo Hangout Logo
Banjo Hangout Logo

Premier Sponsors


 All Forums
 Reso-Related Topics
 Building, Setup, and Repair
 ARCHIVED TOPIC: String height at nut & last fret or saddle on squareck reso?


Please note this is an archived topic, so it is locked and unable to be replied to. You may, however, start a new topic and refer to this topic with a link: http://www.resohangout.com/archive/60074

duganderson - Posted - 06/02/2025:  06:22:07


Any suggestions on string height for a square neck reso?

I got a square neck in great condition used for under $100 but the sting heigh seems to be a low. The nut is shorter than my other reso AND the saddle is shorter and notched quite deeply.

I'm guessing I will need a new saddle. Any suggestions on doing this myself OR bringing it to a shop? Recommendations for new saddle and nut?

hlpdobro - Posted - 06/02/2025:  08:18:05


Beard Guitars/Resophonic Outfitters

hlpdobro - Posted - 06/02/2025:  08:19:35


String height will be determined by the guitar design and height of the coverplate's palm rest.

h

duganderson - Posted - 06/02/2025:  09:52:55


quote:

Originally posted by hlpdobro

String height will be determined by the guitar design and height of the coverplate's palm rest.






Are you suggestion that the string height on the saddle should be as high as possible under the coverplate?  If that's the case, should the string height be similar across the entire fretboard or a bit lower as you get closer to the nut?



 

hlpdobro - Posted - 06/02/2025:  10:05:59


Same height.

With Beard Guitar setups (extended palm rest, Beard cover plates) the height is "just" under the palm rest, perhaps 1/8" or less, while the guitar is under tension/tuned.

I'll caution that depending on the guitar in question you might well be throwing good money after bad due to other factors I am unaware of, like... the spider, cone, design and construction.

Good luck.

duganderson - Posted - 06/02/2025:  10:37:21


quote:

Originally posted by hlpdobro

Same height.



With Beard Guitar setups (extended palm rest, Beard cover plates) the height is "just" under the palm rest, perhaps 1/8" or less, while the guitar is under tension/tuned.



I'll caution that depending on the guitar in question you might well be throwing good money after bad due to other factors I am unaware of, like... the spider, cone, design and construction.



Good luck.






Thanks!    I will make sure I don't dump a lot of money into it.  If it's going to be expense to get it fixed by my local guitar shop, I may use this guitar to practice and develop my setup and/or repair skills (as long as parts are not too expensive).



Does anyone know any good sites, videos, etc. for learning more about setup and basic luthier type skills on a square neck dobro especially related to the saddle?  

hlpdobro - Posted - 06/02/2025:  10:42:39


Is the goal how to learn to play or to tinker?

h

duganderson - Posted - 06/02/2025:  10:43:42


quote:

Originally posted by hlpdobro

Beard Guitars/Resophonic Outfitters






This looks like a GREAT resource.  They have slotted saddles and nuts.  I'm guessing they could provide some phone or email consulation if necessary too!  Dropping in a new nut and sadlle would only be like 30$ or 40$.



 

duganderson - Posted - 06/02/2025:  10:48:51


quote:

Originally posted by hlpdobro

Is the goal how to learn to play or to tinker?



h






I do like both.  Even though the nut and saddle seem too low and uneven, this dobro sounded pretty good to me.  Currently, even as is, this guitar gives me a second dobro to leave in open D so I don't need to retune between songs at my local jam group if I change from GBDGBD to open D.  Also, its nice to have a guitar that I have not put a lot of money into to use to travel, take to the cabin, etc.   AND it came with a nice hard case!!!  I'm not currently wanting to have a lot of money right now tied up into a second dobro.



 


Edited by - duganderson on 06/02/2025 10:49:49

MarkinSonoma - Posted - 06/02/2025:  13:16:39


So I guess you went for the Trinity River guitar?



Adding to what Howard wrote, the classic nut height from the fretboard most reso luthiers use for a squareneck can range from 3/8 to 1/2 of an inch. 

duganderson - Posted - 06/02/2025:  19:04:40


quote:

Originally posted by MarkinSonoma

So I guess you went for the Trinity River guitar?



Adding to what Howard wrote, the classic nut height from the fretboard most reso luthiers use for a squareneck can range from 3/8 to 1/2 of an inch. 






Yes, it was as great deal and I got a nice case too!  

duganderson - Posted - 06/03/2025:  07:24:39


Just found this resource for setup of Spider Bridge dobros. It looks great!

stewmac.com/video-and-ideas/on...8&group=&

MarkinSonoma - Posted - 06/03/2025:  10:42:15


Good - I was going to send that to you but you beat me to it.

SlimPickins - Posted - 06/03/2025:  16:15:00


That StewMac article is great. I reference it regularly when I tinker with my guitars. Dan is a wealth of knowledge and a phenomenal builder. I’m proud to own two of his fantastic guitars (my avatar picture is of my sunburst curly maple and Dan's personal maple guitar).


Edited by - SlimPickins on 06/03/2025 16:16:28

Terms of Use | Privacy Policy | Privacy Consent (EU/GDPR Only)

Copyright 2026 Reso Hangout. All Rights Reserved.





Hangout Network Help

View All Topics  |  View Categories

7.421875E-02