Banjo Hangout Logo
Banjo Hangout Logo

Premier Sponsors


 All Forums
 Reso-Related Topics
 Building, Setup, and Repair
 ARCHIVED TOPIC: Vintage Dobro cones


Please note this is an archived topic, so it is locked and unable to be replied to. You may, however, start a new topic and refer to this topic with a link: http://www.resohangout.com/archive/60345

Hossdog - Posted - 09/17/2025:  03:28:20


Hi All…and thanks in advance for any help offered. I am repairing a vintage, probably Australian built, round neck dobro style guitar for a mate. No markings can tell us when it was made; however, the problem I am encountering probably dates the guitar.
Here the crux of the problem. A new replacement cone was purchased prior to me getting my hands on the guitar and because of the height of the raised ridge on which the spider sits, the spider actually makes hard contact with the cover plate.
Examining my 1936/1937 Model 25 Dobro the cone within does not have an overly pronounced ridge on which the spider sits, and while not flat it is nowhere near as obvious as the replacement cone purchased. I suspect the guitar I am working on had a cone similar to my dobro, and through comparing the two it appears sourcing this older style cone would solve the problem currently faced.
Does anyone know of a manufacturer who makes such a cone, or at least put me in contact with someone who might be able to help?
This guitar is not of great monetary value; however, would like to get the old girl going. It holds sentimental value for the owner.

MarkinSonoma - Posted - 09/17/2025:  13:44:23


I wonder if it's a Beard Legend cone? The "lip" that the spider legs rest on at the edge is a little higher than other cones and makes for a tighter fit under the palm rest.  I'm guessing that the older Beard cone, the BC-1 doesn't have this same issue, but I wouldn't know because I've never had one of those in a guitar.



Other than the original lug cone on my circa 1933 Model 37 Dobro the other cones I have used are Quarterman and Scheerhorn. The 'horn cone was out of stock for awhile at Elderly in MIchigan but they are available again. The "lip" sits lower then the Legend cone, clearance under the palm rest is not an issue. As for Quarterman cones, we amy never see those again for a variety of reasons. 



elderly.com/products/scheerhor...540476480



Another company to try is Replogle here in Northern California. He shows some as being out of stock, but it would be worth a try to see if he can ramp up production again. HIs Standard cone is designed specifically for older Dobro brand guitars.



replogleresos.com



 


Edited by - MarkinSonoma on 09/17/2025 13:45:05

docslyd - Posted - 09/17/2025:  15:27:14


Sounds like the final solution would be to rout the ledge to accommodate the cones that are widely available....and probably preferred as far as sound goes.



SORRY...I just saw your photos.  There's a lot going on here and the cone ledge is inadequate in so many ways.  I'm not sure what other structural deficiencies are present.  The solution is really to reconstruct the cone bearing area of the guitar...posts and ledge.  Probably more than you wanted to find in this can o' worms.


Edited by - docslyd on 09/17/2025 15:30:45

daver - Posted - 09/17/2025:  19:15:32


Hossdog, I have looked at your pictures. I have personally never seen a cone (vintage, Quarterman, Scheerhorn or Beard Legend) with such an exaggerated inner lip. It appears to be the same height as the outer roll, which also looks disproportionally high (could be that the picture makes it look that way). Do you know who manufactured this cone?  I would not expect an off-brand cone to proiduce great tone.



The ideal solution would be to repair/reconstruct the cone ledge and then install a standard cone from Scheerhorn, Beard, or Replogle. Since you are fixing it for a friend, is the goal to just make the guitar playable? If so, the coverplate could be raised to clear this cone and spider. Beard makes coverplate risers (resophonicoutfitters.com/produ...CR-V.html) , perhaps you could fashion a raised ring on your own.  



 

Hossdog - Posted - 09/18/2025:  15:16:46


Thanks to all above for your contributions. I am alas living on the West Coast of Australia, far from any suppliers of Reso cones in Australia, let alone manufacturers in America, so it could be an expensive exercise trying cones until I get one to fit. I have asked Beard to send me profiles of their cones but I am still waiting. Thanks @MarkinSonoma , daver for the leads on other manufacturers and I will ask the same of them too see if I get a reply.
As this guitar is a pawn shop banger Im not going to go and reconstruct it. I’m not comfortable routing out the shelf on which the cone sits as it could leave too little support. I will probably opt for buying a replacement cover, and building a cover ring that will raise the new cover just enough to clear the spider.
Thanks again….Hoss

little ray - Posted - 09/24/2025:  13:27:13


Call Paul Beard for advice. His shop is very good to deal with. I get all my cones from him for rebuilds.

hlpdobro - Posted - 09/24/2025:  14:06:36


Did you check for clearance with the guitar strung up, at pitch & under tension (the correct way) or simply mounting the cone/spider with the cover plate resting.

If the latter, do the former. The cone settles dramatically with the guitar under tension.

I also looked at the photos. The guitar (imho) is in rough shape. I've dealt with worse (ledge rebuild) but questioned the customer's attraction to the particular guitar and expense involved.

h

Terms of Use | Privacy Policy | Privacy Consent (EU/GDPR Only)

Copyright 2026 Reso Hangout. All Rights Reserved.





Hangout Network Help

View All Topics  |  View Categories

0.078125